Gate Parts & Welding in San Leandro — On-Site in 60 Minutes, Fixed the Same Day

Fast, Reliable Gate Parts & Welding Across San Leandro

Gate parts and welding repair in San Leandro typically runs $180–$650 depending on the component, and most hinge, post, or rail jobs are completed same-day. Our crew covers all three San Leandro ZIP codes — 94577, 94578, and 94579 — with David Kaplan, our Owner and Field Supervisor, often on-site himself. Call (833) 805-4890 for a free estimate and we’ll diagnose whether you need a simple hinge swap or full custom welding.

Call (833) 805-4890

We’ve been driving to San Leandro from our Los Angeles base for years, and we know the difference between the bay-front blocks near Marina Boulevard and the inland pockets toward the San Leandro Hills. That local geography matters. The flatland neighborhoods, especially Washington Manor down in 94579, sit just feet above bay level, exposing gate hinges and automatic operators to persistent salt-laden marine air that corrodes mild steel and cast iron far faster than inland East Bay cities like Castro Valley or Pleasanton. We’ve built our repair approach around that reality.

Why Ironwood Gate Repair Los Angeles Is San Leandro’s Preferred Gate Parts & Welding Company

Our 233 verified customer reviews averaging 4.7 stars include plenty from San Leandro homeowners and property managers who found us after a generalist couldn’t finish the job. David Kaplan shows up as Field Supervisor — not a rotating technician you’ve never met. That matters when you’re standing in your driveway with a gate that won’t close and a dog that needs to stay put.

We’re gate-only specialists. Not a garage door company that “also does gates.” Not a handyman with a borrowed welder. Fourteen years focused exclusively on gate repair, installation, automation, access control, and structural welding means we’ve seen your exact failure before. We recently replaced a rusted-out LiftMaster gate operator at a newer master-planned home in the Bayfair area (94577). The builder had installed a basic non-smart opener on a three-car driveway, and within two years the marine air had corroded the circuit board contacts. We upgraded to a Wi-Fi-enabled LiftMaster with myQ and reinforced the hinges with stainless steel to resist the salt spray.

We carry parts for nine major automation brands — including FAAC, BFT, Linear, and Viking — so San Leandro customers aren’t told their system “isn’t supported.” Our in-house welding capability means broken hardware is repaired or fabricated on the spot rather than outsourced or delayed. No waiting two weeks for a bracket to ship from a warehouse in Texas.

Our Gate Parts & Welding Services in San Leandro

Hinge Replacement

Hinge replacement is our most common call in San Leandro, and it’s almost always corrosion-driven. The marine layer hangs low over 94577 and 94578 most nights, keeping gate metal damp until mid-morning. Standard mild-steel hinges last maybe 5–7 years in these conditions; we replace them with marine-grade or stainless-steel hardware that holds up to the salt air. A typical residential hinge replacement in San Leandro runs $180–$320 for a standard swing gate, including labor and hardware. For the heavier wrought-iron gates common in Washington Manor, expect $280–$450 because we often need to realign the entire gate frame after the sagging hinge has pulled things out of square.

Post Replacement

San Leandro’s post-WWII tract homes — those 1940s–1960s builds in Washington Manor and the older blocks of 94577 — were sold with low ornamental iron gates set in concrete pads that have since cracked and heaved. Throwing hinges out of alignment is just the start; eventually the post itself leans or cracks at the base. We pull the old post, pour new concrete with proper drainage (critical in this clay-heavy soil that holds moisture), and weld or bolt your existing gate to a new steel post. Post replacement in San Leandro typically costs $450–$850 depending on gate weight and whether we need to modify the existing frame. David and his team handle the welding in-house, so there’s no delay waiting for a subcontractor.

Rail Repair

Horizontal rails on ornamental iron gates fatigue at the welds over decades of vibration and thermal cycling. In San Leandro, the added corrosion stress means we see rail separations on gates that are 40, 50, sometimes 60 years old. We can often cut out the failed section, fabricate a matching replacement from steel stock, and weld it back in with a finish that blends with the original. For gates where the rail system is too far gone, we’ll tell you straight — no point welding patches on a frame that’s rotted through. Rail repair runs $220–$480 in San Leandro; full rail replacement on a standard residential gate is $380–$650.

Custom Welding

Our Gate Parts & Welding team fabricates brackets, strike plates, catch posts, and reinforcement gussets on-site. This is where San Leandro’s mix of aging residential iron and newer commercial slide gates keeps us busy. Along the I-880 corridor from Davis Street to Hegenberger Road, warehouses and light-manufacturing facilities run high-cycle commercial slide gates that take a beating. The salt air and diesel particulates foul circuit boards and track rollers at a rate that pushes many of these commercial accounts onto annual service contracts rather than call-only repairs. When a bracket cracks or a catch post shears, we cut and weld replacement steel right there. Custom welding jobs in San Leandro start around $200 for simple bracket fabrication and run to $600+ for structural post or frame repairs on heavy commercial gates.

Trusted Brands We Service in San Leandro

We stock and service FAAC, BFT, Linear, and Viking operators and components, plus five additional major brands. For San Leandro customers, this means we don’t have to special-order a circuit board or limit switch and make you wait. We carry common failure parts — FAAC control boards, BFT hydraulic fluid seals, Linear actuator gears, Viking limit switches — because we’ve learned what fails in this climate. The salt air attacks electronics as aggressively as it attacks metal, so having sealed replacement units on the truck saves a return trip. If your operator is fried beyond repair, we can typically source and install a compatible replacement same-day or next-day, programmed to your existing remotes and access codes.

Common Gate Parts & Welding Problems We See in San Leandro Homes

• Builder-grade gate openers on newer homes lose connection or fail entirely due to corrosion from marine air, requiring smart-opener upgrades with sealed electronics. We see this in Bayfair-area master-planned homes where developers installed basic non-smart openers to hit a price point.
• Wrought-iron gates in post-WWII tract homes sag as concrete pads heave, throwing hinges out of alignment and requiring post replacement and custom welding. Washington Manor (94579) is ground zero for this — those original 1940s–1950s gates are now 70+ years old.
• High-cycle commercial slide gates along the I-880 corridor foul circuit boards and track rollers from combined salt air and diesel particulates, needing frequent latch-and-lock repairs. Davis Street to Hegenberger Road is particularly hard on equipment.
• Gate metal stays damp overnight most of the year in San Leandro’s low-lying flatlands, accelerating rust on hinges, strike plates, and automatic gate motor housings in ways that inland Alameda County cities do not experience to the same degree.

Pricing for Gate Parts & Welding in San Leandro, CA

We Also Serve Cities Near San Leandro

Our service radius covers Ashland, San Lorenzo, Cherryland, and Castro Valley from our San Leandro base. Each city has its own gate problems — Castro Valley’s hillside homes deal with different soil and drainage issues than San Leandro’s flatlands, for instance. Wherever you are in the East Bay, our Gate Parts & Welding team brings the same parts inventory and field-welding capability. Same-day response is standard for hinge failures, post separations, and gates stuck open or closed.

FAQs — Gate Parts & Welding in San Leandro